Construction plan Designers Needed

2. PLOT DETAILS Legal Ownership: Owned Land (Block A): Pentagon-shaped plot, 172.42 m² (1,856 sq ft) Layout Status: CMDA approved layout Plot Orientation: West side straight wall, east side irregular (bulging boundary) Plot Dimensions (Block A - What I Own): Point A (SW corner): 0, 0 Point B (NW corner): 0, 14.37m Point C (North): 10.09m, 14.37m Point D (East bulge): ~14m, ~7m (calculated from arc lengths below) Point E (South): 8.32m, 0 Internal boundary measurements: - West wall (A-B): 14.37m (straight) - North side (B-C): 10.09m (straight) - C to D (arc): 11.28m (curved/angled) - D to E (arc): 7.24m (curved/angled) - South side (E-A): 8.32m (straight) Total Area: 172.42 m² (1,856 sq ft) Setbacks Required: West (side): Minimum 0.6m legally required (proposing 2.8m for utilities) South (front): 1.5m minimum East & North: Open boundaries (to be discussed) Important: There is adjacent vacant land (Block B) to the east, but DO NOT include this in CMDA submission as I don't own it. Focus approval on Block A only. 3. SCOPE OF WORK REQUIRED Primary Deliverable: Complete CMDA building plan approval package for Block A (172.42 m²) Drawings Required: A. SITE PLAN Show my plot (Block A) within approved layout Mark surrounding plots, roads, access Indicate setbacks clearly North direction marked B. FLOOR PLAN (Ground Floor) Buildable area after setback: ~132-164 m² (depending on setback chosen) Show proposed utilities in setback area: Stairs (steel, external) - SW zone Lift shaft (integrated) - SW zone Toilet (portable/prefab) - NW zone Critical: East side (C-D-E boundary) to be shown as OPEN with columns only Columns at C, D, E to support roof No wall/enclosure on east side initially This allows future flexibility Show other utilities: Borewell & sump (NE corner if space permits) Electrical panel (SE area) Septic tank (NW area) Main entrance (South) C. ELEVATIONS (All 4 Sides) South elevation (front/main entrance) North elevation West elevation (straight wall) East elevation (showing irregular boundary + open side) Standard commercial height: 4.5-5m floor-to-ceiling D. SECTION DRAWINGS (Minimum 2) Longitudinal section Cross section Show foundation depth, floor slab, roof height, ceiling height E. PLUMBING & DRAINAGE PLAN Septic tank location (NW zone - Vastu compliant) Drainage routing from toilet Water supply from borewell to overhead tank Connection to municipal line if available F. ELECTRICAL PLAN Main electrical panel location (SE zone - Vastu compliant) Distribution board General power/lighting plan (basic level acceptable) G. STRUCTURAL COORDINATION I have structural engineer already appointed Please coordinate column/beam layout with them Verify your plans match their structural design Key requirement: Columns at C, D, E must be designed to support cantilevered roof 4. DESIGN REQUIREMENTS Construction Type: Block A: RCC (Reinforced Concrete) construction Columns: 300mm × 300mm minimum Foundation: Eccentric footings (as per structural engineer) Roof: RCC slab OR steel truss with sheet roofing (architect to suggest) Height: Single story initially (Ground floor only) Future provision: Design to allow G+1 or G+2 later Ensure foundation/columns can handle future floors Functional Requirements: 100% clear interior space (no internal partitions for now) Maximum usable commercial area Separate access to upper floors via external stairs/lift (in setback) Utilities externally accessible (not blocking interior) Vastu Preferences (if feasible): Borewell/water: NE zone Electrical: SE zone Toilet/septic: NW zone Stairs/lift/heavy items: SW zone Main entrance: South (already fixed by site) Note: Vastu is secondary to practical/legal compliance. If conflicts arise, prioritize CMDA requirements. 5. SPECIAL CONSIDERATIONS The "Block B" Strategy: There is vacant land (Block B) adjacent to my plot's east side. While I don't legally own it, I may utilize it in the future. For CMDA submission: Show ONLY Block A in all approval drawings Leave east side OPEN (columns at C, D, E but no wall) This is legitimate - showing unenclosed structure Design roof structure to potentially cantilever eastward (but don't show this in CMDA drawings) Why this matters for you as architect: Design Block A columns (especially C, D, E) with adequate strength Coordinate with structural engineer for potential future load Don't mention "future extension" in CMDA documents Just show a practical open-sided commercial structure I will handle any future development independently - your scope is ONLY official approval for Block A. Reference Plans Available: I have conceptual floor plans showing: Proposed utility locations Setback zones Functional layout I will share these as reference for you to formalize into CMDA-compliant CAD drawings 7. EXPECTED DELIVERABLES FROM YOU Phase 1: Drawings Package Complete AutoCAD drawing set (DWG files) PDF versions of all drawings Calculations sheet (FSI, setback compliance, etc.)

Projekt-ID: 40081987