Best PCB Design Expert at your doorstep!
Dear Client,
I can turned into a PCB board.
Please share me your project details.
We couldn’t stop ourselves from bidding after going through the description as they are an exact match with our skill set and experience.
We have experience in Turn Circuit Layout based PCB design and know all the intricacies required to get the job done with perfection.
With more than 15 Years of experience in PCB Design and Circuit Design in Altium, We can ensure you best quality work and before time delivery.
Following is a brief list of expertise that we are carrying:
1. IOT products development
2. Microcontrollers based circuit design – STM32, STM8S etc
3. Smart Products like Smart watch - GSM/GPRS/GPS etc
4. Wireless Products - BLE/WiFi- ESP32/ESP8266/NRF24L01
5. Low Power Battery Products design – Rechargeable and Non chargeable
6. Power Electronics – Buck, Boost, Flyback etc
Please answer the following questions:
1 What are your future plans with this project?
2. Are there any specific market standards like CISPER you are aiming?
3. What will be ambient temperature of this product?
4. Are there any other specific requirements besides the ones you mentioned
Let’s have a quick discussion for 5 mins where we would formulate a plan of action of how we shall take this project to the horizons of success.
Regards
Avi
Tech Experts
Quality is never an Accident
Hi dear
I am an electronics engineer and have industrial experience of power electronics circuit and PCB layout designing. I can design a PCB layout up to 16 layers. Share your project details further I will provide you the best design. Reviews, changes, and modifications will also be provided without any extra charges until you will get your required design. You can also check my PCB layout designs as samples. For any discussion feel free to contact me.
Thank you
Best regards
Engr. Saddam Gul
Hi, dear client!
I read your requests carefully.
I am an electrical engineer with 7+ years of PCB design and development experience,
please check my portfolio. Also I have advanced knowledge about electronics and rich practical experience.
As far as I am concerned, you will get good results working with me.
I usually use Altium and I have hobby in smaller PCB design.
I will implement all of your requests with the “highest-quality” and “keep deadline”.
This is my working rule and vision.
In terms of time and price, I am willing to make it more convenient than other developers.
I will give you quick response and solutions for problem.
Best Regards. Thanks.
Hi!
I am an Electronic engineer, microcontroller, PCB Board and Layout, C programming expert having past experiences with arduino, pic, AVR, chipkit and Texas instruments microcontrollers
I am waiting for you over the chat.
Thank you!
Hello Sir.
I can complete this project perfectly.
I have 10 years good experience of hardware development.
I have completed a variety of embedded system design and programming by using microcontroller, arm, etc
Board PCB design have been completed by using Altium and Protel99SE.
Hope to cooperate with you.
Hi there,
Do you have gerber file already?
My name is Jaspreet & I'm part of larger embedded hardware and firmware development team.
Please share us more details about your project so we can able to provide you proposal with desired solutions.
Looking forward to hearing from you soon!
Thanks
1 ) I have over 20 years experience of PCB Layout / Hardware / RF / EMI / Firmware designs, we can complete various design and layout requirements.
# 8051 MCU / ARM Embedded system / Arduino / ST32Fx / IM6x / AVR / TI MSP430x / PIC / Ri-Pi
# WIFI / BT / BLE / GPS # LCD / DTV / MD / Web Camera # LED / Lighting
# LCD Inverter / Touch sensor # NIC / LAN / KSZ9031RNX / LAN8720 # IOT / nRFF528x / ESP8266 / TI CC26x
# Battery / Solar Charger # BMS ( Battery Management System ) # Audio / CSR / Codec / AMP
2 ) I can use as below to design and layout
# Altium # Protel99SE # Eagle # PADS # KiCad # OrCad # Allegro # Proteus # DipTrace
3 ) I can communicate well in English, please contact us by e-mail or s-k-y-p-e me (saludpcb) to find out relevant details.
4 ) I also have to provide PCB layout design service ( super low price )
# For PCB layout:
@ 2 ~ 4 Layers -> $0.4 ~ 0.6 USD per pad @ 6 ~ up Layers -> $0.8 ~ 0.8up USD per pad.
# For reprinting of schematic and component, quotation will vary by each case.
# A minimal of $100 USD 2L / $200 USD 4L / $300 USD 6L will be charged for each case.
What I can do are:
# 1,2, 3, 4, 6, 8, .... layers ( PCB / FPCB ) # High Speed and High Density PCB layout
# Differential Signal PCB layout # RF Signal PCB layout # 3D Models / FreeCad
5 ) PCB / PCBA manufacture
# Prototype assembly # Components procurement # High quality # Quick, 24hr lead time # Low cost
Hello..
I am holding masters degree in electrical engineering.. I have very good circuit design and PCB layout.. I have gone through your requirements and I am sure that I can do this project perfectly.. Kindly drop me a message through chat.. Looking forward to work with you for long term..
THANKS
Hello, I can help you with your request. If you look at my portfolio you will see some of my work in pcb design, beyond the design I can advise you on the manufacture of it. I have experience working with suppliers from China like JLCPCB. The product consists of delivering the source file of the pcb made in kicad, and the typical manufacturing files: BOM, GERBERS, PICK and PLACE. Get in touch with me and we'll talk, a greeting.
We have well experienced PCB Layout design professionals in our team to deliver you best class service to increase you product yield on operation.
Our Deliverable are listed below
* Schematic PDF
*Gerber Files
*BOM
*Pick and Place Files
Kindly contact us to discuss further in detail
Sir i will be very glad if you give me this project. Sir i am very good in doing these types of work. Please give me this work i will do it with hard work .
THANKYOU
Hi Sir,
I am Electrical Engineer and have strong PCB designing skills. I have done lots of my projects in which I design my PCBs myself. I believe on Professional and honest hard work. I will do ?% efficient work.
If you find me suitable for these tasks feel free to contact me to further discuss about it.
Thanks.
Thank you for the invitation to bid.
From your brief description, I believe I would be able to deliver on this.
However, I would prefer a few more details about the complexity of the circuit.
I have 10+ years experience in electronic circuits, starting from hobby projects all the way to complex power conditioning equipment. I assure you I’d put in the best of my efforts.
Thank you and looking forward to your acceptance of my bid.
R/Sir,
I’m doing it as my hobby I don’t have any past experience in designing and developing circuits but as an engineer I have full knowledge of circuits and boards if once you provide me an apportunity I will do very sincerely and with full dedication.
Thanks and regards
Kumar praveen
I have over 5 months of internship experience as PCB designer and I have completed many projects on PCB. Please feel to share your layout with me. I will get it done accurate and with in time